BQLMV - FUSER AGENT, 6950
- MSDS: BQLMV
- Manufacturer: PELIKAN INC
- Product Name: FUSER AGENT, 6950
- National Stock Number: 6850-00N035933
Product Identification
Product ID:FUSER AGENT, 6950
MSDS Date:10/10/1991
FSC:6850
NIIN:00N035933
MSDS Number: BQLMV
Responsible Party
DERRY, PA 15627
US
Emergency Phone: 412-694-9600
Info Phone: 412-694-9600
Cage: FO912
Contractor
Telephone: (412) 694-2792
Cage: 47811
Ingredients
DIMETHYL SILICONE (MODIFIED FLUID)
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHAL:MIN RESP TRACT IRRIT MAY OCCUR
ON CONTINUOUS EXPOS TO HIGH CONCS. SKIN:MILDLY IRRIT. EYES:MIN
IRRIT. INGEST:PRACTICALLY NON-TOX. IN A XEROX SPONSERED CHRONIC
INHAL STUDY IN RATS USING A SPECIAL TONER, THERE WERE NO LUNG
CHANGES AT ALL IN LOWEST EXPOS LEVEL (1 MG/CUM) THE MOST RELEVANT
LEVEL TO (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ:POTNTL HUMAN EXPOS. A VERY SLIGHT
DEGREE OF FIBROSIS WAS NOTED IN 25% OF ANIMALS AS MID-EXPOS LEVEL
(4 MG/CUM), WHILE SLIGHT DEGREE OF FIBROSIS WAS OBSERVED AT HIGHEST
EXPOS LEVEL (15 MG/CUM) IN ALL ANIMALS. THESE FINDINGS ARE
ATTRIBUTED TO "LUNG OVERLOADING", A GENERIC RESPONSE TO EXCESS AMTS
OF ANY (SUPDAT)
Medical Cond Aggravated by Exposure:NONE WHEN USED AS DESCRIBED BY
PRODUCT LITERATURE.
First Aid
First Aid:INHAL:REMOVE TO FRESH AIR. SUPPORT BREATHING (GIVE ARTF RESP)
. SKIN:WASH W/SOAP & WATER. EYES:FLUSH THOROUGHLY W/WATER FOR AT
LEAST 15 MINUTES. INGEST:DILUTE STOMACH CONTENTS W/SEVERAL GLASSES
OF WATER.
Fire Fighting
Extinguishing Media:WATER, FOAM, DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NONE SPECIFIED BY MANUFACTURER.
Accidental Release
Spill Release Procedures:USE ABSORBENT MATERIAL TO COLLECT & CONTAIN
FOR SALVAGE OR DISPOSAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:NONE SPECIFIED BY MANUFACTURER.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.
Exposure Controls
Respiratory Protection:NONE REQD WHEN USED AT INTENDED IN COPIER OR
PRINTER EQUIP. FOR USE OTHER THAN NORMAL CUSTOMER-OPERATING PROCS
(SUCH AS BULK PROCESSING FACILITIES), NIOSH/MSHA APPROVED
RESPIRATORS MAY BE REQUIRED. FO R INFO CONTACT MFR.
Ventilation:NONE SPECIFIED BY MANUFACTURER.
Protective Gloves:NONE REQD WHEN USED AS INTENDED (SUPDAT)
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:NONE REQUIRED WHEN USED AS INTENDED IN
COPIER OR PRINTER EQUIPMENT.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
EFTS OF OVEREXP:DUST RETAINED IN LUNGS FOR PRLNG INTERVAL. SPECIAL TEST
TONER WAS 10 TIMES MORE RESPIRABLE THAN COMMERCIALLY AVAIL TONERS
TO COMPLY W/EPA TESTING PROTOCOL & WOULD NOT FUNC PROPERLY IN A
COPIER OR PRINTING EQUIP. PROT GLOVES:IN COPIER OR PRINTER
EQUIPMENT.
Chemical Properties
HCC:N1
Spec Gravity:1.0
Solubility in Water:NEGLIGIBLE
Appearance and Odor:COLORLESS LIQUID; SULFUR ODOR.
Stability
Stability Indicator/Materials to Avoid:YES
OXIDIZING MATERIAL CAN CAUSE A REACTION.
Stability Condition to Avoid:NONE
Hazardous Decomposition Products:SIO*2 & TRACES OF INCOMPLETELY BURNED
CARBON PRODUCTS.
Conditions to Avoid Polymerization:HANDLING AT ELEVATED TEMPERATURES.
Disposal
Waste Disposal Methods:DO NOT INCINERATE. NO SPECIAL TECHNIQUES BEYOND
NORMAL PRACTICE. INSURE CONFORMITY W/FEDERAL, STATE & LOCAL
REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.